| Capabilities |
|
| Programming Interface |
Can be programmed and controlled
via an RS-232 serial connection to a PC, or an RJ-45 ethernet
connection to a PC or LAN |
| Call Types Supported: |
|
| Call Originate |
TSP places calls to the device under
test |
| Call Terminate |
TSP receives calls from the device
under test |
| End to End |
Calls placed through the TSP by
one device to another. Four call types are available:
Dialed (for dynamic routing by assigning a telephone
number to each channel)
Switch Emulation (simulates call through the central
office with any two channel protocols except Clear Channel)
Channel Bank (for T1/E1 loop start foreign exchange
channel to POTS channel)
Clear Channel (for 64 Kbps data) |
| Phone Numbers |
Up to 40 digits on all POTS and
T1/E1 channels |
| Message Playback |
8 kHz, 8 bit mu-law or a-law encoded,
WAV files assigned to play after call is established for Call
Originate and Call Terminate operation or from user scripts.
Messages that are less than 8 seconds in length, with a total
combined length of 24 seconds or less, will be downloaded
into the TSP and stored in non-volatile memory. If any messages
are longer than 8 seconds, or the combined length exceeds
24 seconds, some
messages will be streamed to the TSP in real-time over the
network connection. |
| Simulator Activation |
Manual or timed |
| Diagnostics |
Monitor and manual control of signaling
state on channels |
| Protocol Analyzation |
Monitors the AB bit states for D4
and ABCD bit states for ESF on T1 and E1 channels. The Call
Tracing feature gives a step-by-step display of the call progress
signaling on a POTS, T1, E1 or PRI channel. |
| Event Log |
Time stamped listing of system and
channel specific events and call records |
BHCA
(Busy Hour Call Attempts) |
>48000 (2 T1s, Wink Start)
For details, see App Note
109, TSP Call Rate Calculators |
| T1/E1 Interface |
|
| Connector Standard |
RJ48C |
| Transmit Level |
3.00 V (Nominal) for 120 ohms |
| T1 Parameters |
|
| Framing
Formats |
D4 or ESF |
| Line Coding |
AMI or B8ZS |
| Clocking |
Internal or External |
| Line Build-out |
0-655 ft or -7.5 dB to -22.5 dB
line loss |
| E1 Parameters |
|
| Signaling
Formats |
FAS or CAS |
| Line Coding
|
AMI or HDB3 |
| Impedance |
120 ohms |
| PRI Parameters |
|
| T1 Switch
Type |
US National ISDN-2 (NI-2)
Lucent 4ESS and 5ESS (TR41459)
Nortel DMS-100 and DMS-250 |
| E1 Switch Type |
Euro-ISDN |
| Capabilities |
• Direct Dialing In (DDI)
• Delivery of Caller Number (CLIP) and Called Number
• Delivery of Type of Address and Numbering Plan
• Subaddressing |
| Simulation |
Terminal Equipment (TE) or Network
(NT) end |
| Signaling Protocols |
ITU Q.421, Wink Start (i.e. E &
M), Immediate Dial, Delay Dial, Loop Start FXS, Loop Start
FXO, Ground Start FXS, Ground Start FXO, Clear Channel (64
Kbps, no signaling) |
| DTMF Generation |
Generates up to 16 DTMF digits in
band on the T1/E1 channel when placing a call into the equipment
under test |
| POTS FXS Interface |
|
| Connector Standard |
RJ-11 (4 channel POTS module) and
RJ-14 (8 channel POTS module) |
| Loop Current |
20 mA minimum |
| Battery Source |
On-hook 60 VDC minimum |
| Ringing Source |
42 VAC |
| Ring Cadence
on cycle
off cycle |
Cycles
2 S
4 S |
| Ring Frequency |
20 Hz |
| Impedance |
600 ohm |
| Audible Ringback |
440 Hz + 480 Hz @ -12 dBm composite |
| Dial Tone |
350 Hz + 440 Hz @ -12 dBm composite |
| Busy Tone |
480 Hz + 620 Hz @ -12 dBm composite |
| POTS FXO Interface |
|
| Connector Standard |
RJ-14 |
| Ring Detect |
40 Vrms minimum |
| REN |
0.0 |
| Loop Current Detect |
10 mA minimum |
| Line Impedance |
Optimized for a 900 ohm AC line impedance. |
| DTMF Transmit Level |
-10 dBm averaged over 3 seconds |
| Audio Message Playback Level |
Less than -10dBm averaged over 3 seconds |
| Dialing Mode |
DTMF only |
| Configuration |
|
| Network Interface Modules |
Single Port T1/E1, Dual Port T1/E1,
4/8 Channel POTS FXS, 8 Channel POTS FXS, 8 Channel POTS FXO |
| TSP Configuration Software Platforms |
Windows 95/98/2000/XP, Windows NT |
| Power |
|
| AC |
90-250 VAC, 43-63 Hz |
| Physical Dimensions |
|
| Size |
|
| Base |
17.5" X 10" X 1.8" |
| Modules |
2.82" (W) X 3.8" (L) |
| Weight |
4 to 4.5 lbs. |
| Environmental |
|
| Operating Temperature |
0°C to +40°C |
| Storage Temperature |
-20°C to +70°C |
| Regulatory |
|
| Safety |
|
| United States |
UL 3111-1 |
| Canada |
CSA C22.2 No. 1010-1 |
| European Union |
EN61010 European Safety Requirements
for Electrical Equipment for Measuring, Control, and Lab Use |
| EMC |
|
| United States |
FCC Part 15 Class A |
| Canada |
CISPR 22/85, Class A |
| European Union |
EN61326 Class A for Laboratory Equipment
|
| Telecom |
(Only applies to TSP-8PFXO-01
Module) |
| United
States |
FCC Part 68
Certification Number US: AHHMA00BTSPU8PFXO |
| Canada
|
Industry Canada CS-03
Registration Number: 344A-TSP8PFXO |
| FCC and Industry Canada
REN |
0.0B |
| Warranty Info |
Teltone warrants this product to be
free of defects in workmanship and materials for a period of
1 year. |
